FEATURESExnt long term stability (4 ~ 20mA, 500Ω);Precision measurement even for distorted wave (S3-AD-1T);High impulse & surge protection (5KV);The case can be mounted on a 35mm rail which complies with DIN 46277;Model:Accuracy: ± 0.2% ROS3-AD-1 : 1Ïinput (AVG.)S3-AD-3: 3Ïinput (AVG.) S3-AD-1T: 1Ïinput (TRMS)Accuracy: ± 0.5% RON3-AD-1 : 1Ïinput (AVG.)N3-AD-3: 3Ïinput (AVG.) N3-AD-1T : 1Ïinput (TRMS)Sinusoidal Waveforms ï¼ AVG.S3-AD Series Transducer converting a sinusoidal alternating current into a dc output, proportional to the RMS value of input. These units are average sensing, but RMS calibrated for a sine wave with less than 1% distortion. The input ted to a dc voltage which then feeds to a single stage amplifier and a dc output produced.Non-Sinusoidal Waveforms ï¼ TRMSS3-AD-1T ,N3-AD-1T Transducer are designed for use on waveforms with up to 30% of 3rd harmonic content. The input an RMS detection circuit and the resultant dc volts produced are a nction of the RMS value of input waveform. This dc voltage is converted to a milliamp output via an output amlification circuit.INPUT-OUTPUT CURVESPECIFICATIONï¼INPUTï¼Input Range Input Burden Input Frequency Max. Input Over capability0 ~ 1A <- 0.1VA 50Hz ± 3Hzor 60Hz ± 3Hz 3 X rated continuous 10 X rated 10 sec.50 X rated 1 sec.0 ~ 5A OUTPUTï¼DC Output Range LoadResistance Output Resistance Output Ripple Response Time0 ~ 1V 1Kï <-0.05ï <- 0.5% RO.(Peak) <-400mS. 0 ~ 99%0 ~ 5V 1 ~ 5V 0 ~ 10V 0 ~ 1mA 0 ~ 10Kï 20Mï 0 ~ 10mA 0 ~ 1Kï 5Mï 0 ~ 20mA 0 ~ 500 ï 4 ~ 20mA Aux. power supply AC 110V ± 15%, 50/60HZAC 220V ± 15%, 50/60HZDC24V, 48V, 110V, ± 15%Power consumption -2.5VA, â¤DC 3WPower effect â¤0.1% ROWaveform effect â¤0.2% RO. at distortion factor 30%( PCIR)Output load effect â¤0.05% RO.Magnetic field strength -0.2% RO., 400A/MSpan adjustment range 5%ROZero adjustment range 1%ROOperating temperature range 0 ~ 60âOperating temperature range 0 ~ 60âStorage temperature range -10 ~ 70â Temperature coefficient - 100PPM from 0 to 60â⤠60PPM, 25ãC ± 10âMax. relative humidity 95%Isolation Input/output/power/caseInsulation resistance 100M ï, DC 500VDielectric withstand voltage Between input/output/power/case(IEC 414, 688,ANSI, C37) AC 2.6KV, 60HZ, 1 min.Impulse withstand test 5KV, 1.2 X 50μS(IEC 255-4, ANSI C37 90a) Common mode & differential modPerformance Designed to comply with IEC688Safety requirements IEC 414, BS5458CONNECTION DIAGRAMï¼âS3-AD-1, S3-AD-1Tï¼N3-AD-1,N3-AD-1T âS3-AD-3,N3-AD-3 THE OUTSIDE DIMENSION (UNIT: mm)âS3-AD-1, S3-AD-1T:N3-AD-1,N3-AD-1T: âS3-AD-3,N3-AD-3: