Japan Toyooki defoamer machine 400L, 350L, 200L

Xiamen Yingxinfeng Import and Export Co., Ltd. agent sales of Japan TOYOOKI defoaming machine Japan Mitsubishi MITSUBISHI defoaming machine

Eliminate the floating bubbles that occur on the surface of the tank and restore the liquid state.

Effect: Prevent the bubble from exceeding the upper limit

* Can surely prevent bubbles from exceeding the upper limit.

The upper limit was exceeded due to forgetting to put in the defoamer

There is no need to worry about the situation that the factory bed is dirty, the liquid is insufficient, the equipment malfunctions, and the liquid flows out.

No defoamer needed

* It can save the cost of defoamer, time and manpower for placing defoamer.

The defoamer lasts for a short time and the effect is semi-permanent if you set "BABUKESU".

*Don't worry!! After adding defoamer, it will affect the performance of the product.

save space

* To prevent bubbles from exceeding the upper limit, it is not necessary to make the tank larger.

The size of the liquid tank can be reduced to the minimum possible.

Principle The foam is sucked in from the suction port, and the foam is eliminated by the telecentric force of the internal rotating body.

The eliminated foam turns back to liquid and ejects from the outlet.

Japan Mitsubishi BK series automatic defoaming machine

save space

● To prevent the foam from exceeding the upper limit, it is not necessary to make the tank larger.

The size of the liquid tank can be reduced to the minimum possible.

Use a 100W motor (about twice the conventional type!) to achieve a defoaming power of 200L/min, with a maximum capacity of 600L/min. How about you

<type>

・Three series

・Motor (100W / 200W / 400W)

・Material (normal steel, stainless steel)

・Voltage: Three-se 200V AC

(A1 type 100V accepts production)

<Compatibility with old types>

BKN200 (BK100/200) is available

Instructions

・Coolant device

・Food cleaning process

・Beverage production process

・Semiconductor cleaning process

・Fiber dyeing

·size

·production process

・Finishing process

Applicable equipment

●Metal processing equipment, chemical equipment, food equipment, rmaceutical equipment, electronic related equipment, etc.

Just put the defoaming device on the tank, you can quickly remove the bubbles on the liquid surface, while improving the working environment and reducing the consumption of defoamer.

The operation manual of the defoaming equipment "Babukesu" Principle sucks bubbles through the suction port, and crushes them by the centrifugal force of the internal rotating body. The crushed foam turns into liquid and flows out from the outlet like a shower. 2. How to use (1) Just connect the power supply and use it immediately. (This product does not include a power cord or power box.) (2) There is no restriction on the direction of rotation of the motor. (3) Ensure to provide an overload protection device for the motor. (4) As shown in the standard installation drawing, install the suction port on the water tank vertically. (5) When installing at the installation position, the end surface of the suction inlet should be 30 to 100 mm higher than the maximum liquid level of the water tank. If the suction port is blocked by liquid, air bubbles may not be absorbed, and the motor may be overloaded. If the exhaust air hinders the suction of air bubbles, adjust the installation height. When installing, do not block the liquid outlet. If closed, liquid may overflow from the upper part of the mounting surface. (6) The fine dust floating on the foam may be inhaled as it is. (When mixed with liquid, it will come out of the discharge port.) However, if the foam contains a large amount of abrasive powder, if used for a long time, the abrasive powder may accumulate and block the suction port and the discharge port. Check and clean the opening to prevent clogging. If large chips may be sucked in, cover the suction port with a net cover or similar. (7) Do not insert fingers or other objects into the product openings (oil suction port, liquid outlet, motor output shaft). The rotating body inside may cause personal injury or equipment damage. 3. The main specifications of available liquid coolants, cleaning fluids, other liquids (please consult us for high temperature liquids and corrosive liquids) Type material: ordinary steel BKN200 (-A1) BKN400 (-A1) BKN600 (-A1) Material: stainless steel BKN200S (- A1) BKN400S (-A1) BKN600S (-A1) defoaming capacity (1 minute) 200L400L600L rated voltage unsigned: three-se AC200VA1: single-se AC100V motor output kW 0.10.20.4 rated current A (50/60Hz) 200V: 0.52 / 0.48 100V: 1.60 / 1.65 200V: 1.10 / 1.0000V: 3.20 / 2.85200V: 1.90 / 1.80 100V: 5.80 / 5.60 No rotation direction forward and reverse limit mass 200kg: 9.5100V: 11200V: 10100V: 12200V: 18100V: 21 *These The materials are parts other than motors. The stainless steel material is SUS304. *Defoaming ability is a guide (depending on the quality of the foam). Foam liquid tank cover base 30-100mm maximum water level discharge port suction port discharge port