Roland DWX-4W Wet Dental Mill

MODELGX-300GX-400GX-500GX-640Cutting methodMedia-movement methodDriving methodDigital control servo motorFriction feed/Digital control servo motorMaximum cutting area29 x 984-1/8″(737 x 24,998mm)39 x 984-1/8″(1000 x 24,998mm)47 x 984-1/8″(1195 x 24,998mm)Width: 65″ (1651 mm)Acceptable media width2 to 36″(50 to 915mm)3-1/2 to 46″(90 to 1178mm)3-1/2 to 54″(90 to 1372mm)5-1/16″ to 72.5″ (130 mm to 1842 mm)Maximum cutting speedDuring cutting: 33ips (850mm/sec.) [in all directions]During tool-up: 47 ips (1202mm/sec) [in 45º direction]During cutting: 33.5″/sec (850 mm/sec) (in all directions)During tool-up: 47″/sec (1202 mm/sec)Cutting force20 to 350 gf1 to 85 cm/sec (in increments of 1 cm/sec), 20 to 350 grams force (increments of 10 grams) >Mechanical resolution0.00049″/step (0.0125mm/step)0.000137″/step (0.0035 mm/step)Software resolution0.00098″/step (0.025mm/step)0.000984″/step (0.025 mm/step)Distance accuracyError of less than ± 0.2% of distance traveled, or 0.00039 (0.1mm), whichever is greaterError of less than 0.2% of distance traveled, or 0.00394″ (0.1 mm), which is greaterRepetition accuracy0.1mm or less (excluding stretching/contraction of the material)Range for assured repetition accuracyFor materials with a width exceeding 24″ (610mm): Length 157-7/16″ (4000mm) (GX-400/500 only)For materials with a width of 24″ (610mm) or less: Length 314-15/16″ (8000mm)0.004″ (0.1 mm) or lessInterfaceSerial (RS-232C compatible), USB (Rev. 1.1)Serial (RS-232C-compatible), USB (Rev 1.1)Buffer size8MB (2MB for re-plot buffer)2 MB (buffer size: 8 MB)Power supplyAC 100V to 240V +/- 10% 50/60Hz 1.2AAC 100V to 240V =/- 10% 50/60Hz 1.1AAC 100V to 240V ±10% 50/60Hz 1.2APower consumptionApprox. 95WApprox. 100WApprox. 100WAcoustic noise levelCutting mode: under 62 dB (A) Standby Mode: under 40 dB (A) (According to ISO 7779)Dimensions with stand45-1/16(W) x 28-5/8(D) x 43-13/16″(H)1144(W) x 727(D) x 1113mm (H)55-3/8(W) x 28-5/8(D) x 43-13/16″(H)1407(W) x 727(D) x 1113mm(H)63-1/16(W) x 28-5/8(D) x 43-13/16(H)1602(W) x 727(D) x 1113mm (H)83-1/4 (W) x 28-5/8 (D) x 43-13/16 (H) in (2155 (W) x 727 (D) x 1113 (H) mm)Weight with stand97lb. (44 kg)112.4lb. (51 kg)121.2 lb. (55 kg)141.1 lb (64 kg)Operating temperature41 to 104F (5 to 40C)Operating humidity35 to 80% (non-condensing)Standard accessoriesPower cord, blade, blade holder, alignment tool, cable clamp, replacement blade for separating knife, Roland Software Package CD-ROM (CutStudio design software, plug-ins for CorelDraw 10/11/12 and Adobe Illustrator 9/10/CS), startup guide, user manualPower cord, blade holder (XD-CH2), pin, blade, blade (ZEC-U5022), alignment tool, cable clamp, replacement blade for sheet cutter, USB cable, Roland software CD-ROM, setup guide, user’s manual