The OK1052-C consists of SoM and carrier board and is an industrial grade item with working temperature ranges from -40℃ to +85℃. Periral pins such as UART， Ethernet， USB， CAN， PWM， ADC， LCD and CAMERA are all available on carrier board. What's more, OS uClinux is supported very well.
Industry/ Application
| SoM FET1052-C Basic Information | |||
| CPU | i.MX RT1052 | Power Input | 5V |
| Architecture | Cortex-M7 | Dimensions | 31mm* 43mm |
| Frequency | 528MHz | Craftwork | thickness 1.6mm, 4-layer EING PCB |
| RAM | SRAM: 512KB, SDRAM: 16MB/ 32MB | Connector | 2* 80-pin, pitch of 0.8mm |
| Flash | QSPI NorFlash: 4MB/ 16MB | Working Temp | -40℃ to +85℃ |
| SoM FET1052-C Hardware Features | ||
| Interface | QTY | Spec. |
| LCD | 1 | upto RGB888, resolution up to 1366* 768*(WXGA), 480*x 272 and 800* 480 are available |
| Camera | 1 | 8-bit DVP, up to 5.0Mp |
| SD/ MMC/ SDIO | ≤2 | SD card or SDIO card with 1-bit or 4-bit mode |
| USB | 2 | 1x USB2.0 OTG(up to 480Mbps), 1x USB2.0 host, integrated with HS USB |
| SAI | ≤3 | up to 3x IIS audio |
| SPDIF | 1 | Sony/ lips digital audio interface |
| UART | ≤8 | each up to 5.0Mbps |
| SPI | ≤4 | full duplex enhanced sync. serial interface, up to 52Mbit/s, it could be configured to host/ device mode, four chip selections are available |
| IIC | ≤4 | |
| Ethernet | ≤1 | 10M/ 100Mbps |
| PWM | ≤32 | |
| SWD | supported | |
| Keypad | supported | 8* 8 |
| QSPI | 2 | |
| CAN | ≤2 | CAN2.0B |
| ADC | ≤20 | 2x 12-bit ADC, up to 20 input channels |
| ISO7816-3 | ≤2 | |
| SEMC BUS | 1 | 16-bit parallel bus |
| OK1052-C Carrier Board Features | ||
| Interface | QTY | Spec. |
| LCD | 1 | RGB565, resolution up to 1366* 768*(WXGA) |
| Camera | 1 | 8-bit DVP, up to 5.0Mp |
| Audio | 1 | 1x MIC, 1x /td> |
| USB Host | 1 | USB2.0(up to 480Mbps) |
| USB OTG | 1 | standard micro USB connector, USB2.0 OTG(up to 480Mbps) |
| Ethernet | 1 | 10M/ 100Mbps, RJ-45 |
| RTC | 1 | RX8010SJ chip, CR1220 |
| EEPROM | 1 | 24C02 chip with capability of 256 bytes |
| TF card | 1 | compatible of MICRO SD, SDHC |
| LED | 1 | users indicator |
| POR_BUTTON | 1 | reset key |
| WakeUp | 1 | |
| ON/ OFF | 1 | keep pressing it to power on or power off the board |
| BOOT | 1 | DIP switch for booting mode selection, presently, only TF card mode and QSPI NOR Flash mode are supported |
| PWM | 1 | for LCD backlight adjusting |
| ADC | 5 | 4x ADC for resistive touching panel, and 1x ADC for adjustable resistor |
| IIC | 1 | for mounting of touching, camera, WM8960, EEPROM, RTC, IIC converted to 4- chip |
| CAN | 1 | CAN2.0 |
| SPI | 1 | pin connectors (10-pin) with pitch of 2.0mm |
| UART | 1 | 3 3V, up to 5.0Mbps, 10-pin header with pitch of 2.54mm |
| IIS | 1 | for WM8960 |
| Debug | 1 | RS232, DB9 connector |
| SWD | 1 | debug port, 8-pin hearder with pitch of 2.54mm |
| Resistive touching | 1 | the carrier board compative the original touch and TSC2007 touching chip, TSC2007 is the default configuration |
| Keypad | 1 | 4* 4 metrix keypad port by 8-pin header with pitch of 2.54mm |
Overview of OK1052-C
Signup today to claim your Discount. Get Started before it's too late!
