6m Vehicle Mounted Aluminum Pneumatic Telescopic Mast For CCTV Camera

Product Description What is a Pneumatic Mast?            Pneumatic masts are a type of elevation solution using compressed air to raise the central column to its extended height. The masts can either be locking, which each section locks into place once it reaches its maximum extension - designed for safety and long term use( do not lift down the mast), or non-locking where each section sits on cushion  of air- more appropriate for short time using. Classification of masts Model"AT8"---no cable and no lock, for Short time using and small head load. Model"AT9"---with lock. for long time using and large head load. Model"AT7"---with cable. for mounting camera, lights or antenna. Common application Telecommunications, Surveillance, Broadcasting, Disaster Recovery, Site Surveys, Energy Production,  Site so on. Mast specification Available Extended height:2m to 30m Head load capacity:5kg to 300kg. Lift operation choose If no electricity and head load is not heavy, lift control could be foot pump or hand pump---manual lift. If thers is electricity and head load is heavy, lift control should be air compressor, easily and quickly. Specification 30kg head load 6m pneumatic camera telescopic mast Model No. TAL-P6-1.95-30 Extended height 6m Retracted height 1.95m Max head load 30kg Sections Numbers 4 sections each section tube OD& thickness 1#   98/4.0mm      2#    82/3.5mm  3#   66/3.0mm      4#    51/3.0mm Mast net weight 18kg( without  accessories) Max wind load 110km/h ( with guy wire fixed) Detail 30kg head load 6m pneumatic camera telescopic mast Operation steps 1.check the mast in good condition 2.fixed the mast on the ground. tripod fixed diameter is 3.4m,guy wire fixed diameter is 8m. 3.air inlet of control valve connect with air compressor. 4.air outlet of control valve connect wtih the mast. 5. once all mounted, you must keep the lifting control valve handle bar in middle location. (it make the air do not come into mast) 6.open the air compressor switch, at same time adjust the pessure regulating switch to reach 0.2MPa which the pressure gauge shows. 7.then pull up the lifting valve handle bar, mast will rise. 8.if you want to make the mast stop in some height, just make the handle bar in middle. 9. when lift down the mast, please pull down the lifting control valve handle bar.. accessories model unit guy wire 1 set ground anchor 1 set air compressor or manual pump 1 unit tripod or car clamp 1 unit top plate 1 unit bottom base 1 unit more details as follows Swift mast cover with the pulling wire rings Warning that the mast fully retracted. And protect the mast Car Clamps for vehicle mounting mast. Assist the pole to be fixed to a truck or car The rings for fixing the pulling wire when mast without the tripod and no mounting fixed accessories Control box:With the swift for up and down, small air compressor Air pipe,Pressure gauge Basic guy accessories manual hand pump Packing & Delivery 30kg head load 6m pneumatic camera telescopic mast Packing details C/NO. DESCRIPTION QTY (UNIT) N.W. (KG) G.W.  (KG) MEAS (CM) 1 Pole : ------------------1 unit accessories---------1 set 1 50.00 70.00 230*30*40 Certifications Our Service we supply telescopic mast up to 35m,usually used as antenna mast,communication tower,light support,camera mast and so on,custom-made payload to 400kg,customized length,retracted,payload etc. accepted. catalog of some common grade pneuamtic mast as follows extended height (m) No. of section retracted height (m) outer tube range (mm) max. head loads(kg) self weight (kg) 2 2 1.3 118-98 150 22 3 4 1.1 87-43 30 25 6 5 1.7 118-51 30 42 8 7 1.8 140-36 30 65 10 7 2.20 140-36 30 72 12 7 2.6 140-36 15 85 15 7 3.0 140-36 20 90 16 8 3 180-51 30 175 18 10 3 279-66 100 330 20 9 3.3 229-66 55 300 30 13 4 316-51 30 630 3.6m 500kg payload pneumatic mast click pictrues to get more views 2m to 4m small mast for car winch driven mast 20 meter Welcome to contact Company profile