Quick Details
- Processing Time:2-3 days
- Port:SHEKOU
- Supply Ability: 1000 Sets Per Month
- Brand Name:ESMAI
Bonding Press Machine for Silicone O Ring Gaskets
【Product Description】
The silicone extrusion gaskets bonding machine ES-001 is designed for bonding the silicone extrusion gaskets &tubings into o ring Shapes.With the help of htv silicone adhesives(Available from
us) , The extrusion profiles reach a permanant bond in 8-15 seconds with temperature around 175 degrees ,Bonding time and temerature at your adjustment ,Fast working efficiency.
【Technical Data】
Model No.: ES-001
Mold Material : Copper
Upper Mold size: 40*80*13mm(Mold Thickness Ajustable)
Down mold size : 40*80*13mm(Mold Thickness Adjustable)
Copper Mold Temperature Range:0-400℃
The Fast working frequency:1000 times/hour
Working Air Pressure: 4-6bar
Power Input: AC220V 1200W
Net weight: 20KGS
Input Pressure: 6KG, Maximum pressure :40KG
Machine Size: L400*W300*H400mm
【Product Advantage】
1, Fast and Efficient Bond & Increase Productivity of Silicone O Rings .
2, The Copper mold is detachable from the original heat mold
3, Mold opening service is available from us based on your silicone profile sizes for standard square and round shape.
4,The mold thickness can be customised if your silicone profile size is bigger. the
maximum mold thickness can reach 50mm
diameter
5,Machine Movement stable by adopting pneumatic cylinder,Foot padel to control upper mold closing down , hands
free.
Mold pressure ,heating temperature and time at adjustment,Self counting capability.
【Processing】
1, Fix the groove-opened mold on the heating plate,Turn on power and connect the air source,Set the heating temperature on the temperature controller(based on product size), Set the time which
decide the heating time needed for bonding the silicone gaskets,Mixed evenly the silicone adhesive ES-100-A and
ES-100-B and distribute the silicone adhesive ES-100-AB evenly on the PET Sheet for better dipping and near amount of adhesive consumption for each dipping .
2, Preheat by pressing the silicone gaskets ends against the hot copper mold for 2-3 second for a more
strengthened bond.
3, Dipping the two
silicone gaskets ends with silicone adhesive on the PET Sheet .
4, Place the silicone gaskets in the copper mold and press the silicone gaskets ends joining together to
secure they contact well for good bond.
5, Tread on the foot padel and the upper mold will come closing down, wait for heating 8-10 seconds and the
bonding process is completed .
6,take out the bonded silicone O rings from the mold after the upper mold goes up .
【Packing】
Wooden Case Packing ,1~5 Set/Case (Gross Weight Around 25kgs For One Set)
【Safety Note】
1: Please read carefully the manuals before operating the machine, and new operators must pass job training tests.
2: Please check the power plug and air plug and confirm both have been connected correctly. Make sure that the earth wire is connected reliably with the device’s body, and check all components
that have been installed firmly.
3: In the operation, operating the same machine at the same time by two or more people is banned.
4: In the event of abnormal operation should immediately turn off the air supply firstly, then shutting down power switch. After that, the professionals must check and treat the machine.
5:Pull off the air pressure tube and shut down all the power while the machine not working also turn off the power while you have to change the mold in case of touching electricity.
【Routine Maintenance】
To extend service life, please maintain the equipments and confirm that they are in good condition, mainly depending on the following rules:
1: Environment: keep the working environment clean, without dust
2: Power: stable power supply, if not, voltage stabilizer will be necessarily installed on the machine.
3: Air supply: Keep the compressed air clean, without any dust, and let out the polluted water from the filtering cup regularly.
4: Keep the equipments clean, and confirm the moving part without dust interference. If not using the machine for a long time, please coat rust-proof oils on the adjusting screw rod, pack it well
and arrange it properly.
5: Add the lubricating oil on the moving part of the equipment.
6: Before bonding tubes, please check the pressure and temperature of upper and lower copper-formed mould, and ensure its bonding groove clean
