Skf CMXA80 Microlog Vibration Analyzer - USED

SKF CMXA80-F-K-SL Portable Data Collector/ FFT Analyzer is the SKF Microlog Analyzer AX is the most advanced large screen route based analyzer offered by SKF today. The SKF Microlog AX’s features allow you to capture a wide range of vibration data quickly. The analyzer provides the flexibility to support applications that are most important to your company’s specific predictive mainte- nance program. Developed for use in a wide range of industries, the SKF Microlog AX series is approved for use in hazardous environ- ments requiring ATEX, IECEx and Class I Division 2 certifications. SPECIFICATIONS : Performance characteristics Acceleration, velocity, and displacement from hand-held or installed vibration sensors or monitoring systems    • AC / DC sensors • Pressure sensors • Temperature sensors • Keyboard entry: Measurements read from indicators or installed instruments entered in engineering units • Universal tachometer • Visual inspections: Added to measurement as coded notes Enveloper (demodulator)    With four selectable input filters for enhanced bearing and gear mesh fault detection gE filter selections    • 5 Hz to 100 Hz • 50 Hz to 1 kHz • 500 Hz to 10 kHz • 5 kHz to 40 kHz Input parameters    • Tachometer: TTL / analogue programmable to ±25 V • RPM range 1 to 99 999 • Tachometer power supply output 5 V at 100 mA Input over-voltage protection    • AC ±50 V peak • DC ±50 V sustained Dynamic range    >90 dB (24 bit ADC sigma-delta) Input connectors    • CH1: Six pin Fischer CH1, CH2, CH3, CH4  (labeled R) (ICP/AC/DC input), strobe out • CH2: Six pin Fischer CH2 and CH3 (ICP/AC/ DC input), 5 V tachometer out • USB HOST/CHR: Seven pin Fischer R (ICP/AC/ DC input), USB HOST, audio out • USB DEV/TRIG/PWR: Seven pin Fischer USB  DEV, charger, external trigger aux, 5 V  tachometer out Input signal range    ±25 V maximum Signal    RMS/Peak/Peak-Peak/True Peak/True Peak-Peak Transducer check    Bias Voltage Integrity (O/C and S/C detection) Auto range    Yes Frequency range    DC to 80 kHz Bearing condition    gE FFT resolution    100 to 25 600 lines Time block length    256 to 65 536 samples Alarms    Overall, Spectrum and Exponential (Peak and RMS level) Measurement Range    • Route measurements: DC to 80 kHz • Non-route measurements: DC to 80 kHz Averaging    1 to 255 time averages, 1 to 4 096 spectral  averages Averaging type    RMS, Time, Peak Hold, Exponential Cursor    Fixed and cursor lock. Single, har monic and peak pick. Trigger modes    Free run or external trig ger (trigger slope and amplitude) Resolution    Programmable 100, 200, 400, 800, 1 600,  3 200, 6 400, 12 800 and 25 600 lines Measurement windows    Hanning, flat top, hamming and rectangular Measurement parameters    Acceleration, velocity, displacement, gE, temperature, phase, voltage, user specified Measurement types    Overall, spectrum, time waveform, cross phase, orbits, shaft centerline Multi-point automation    Up to 12 meas urements can be listed for one button push automated data collection at each measurement location Accuracy    ±2.5% of full scale range Data display    • Single and dual channel spectrum, single and dual channel time, phase table, process, orbit, cross channel phase • Simultaneous spectrum, time waveform, peak hold averaging • Up to 12 bands (fixed or order base) downloadable from host software Power Battery    • Li-ion smart battery pack • Eight hours continuous operation minimum Physical data Dedicated keys    Up, down, right, and left two enter keys for right and left hand operation, four function keys Hot keys    Peak find, harmonic, expand LCD screen    6.4 in. VGA color transflective TFT LCD screen for indoor and outdoor use, 640 ™ 480 pixels resolution, 16-bit color Case    EN60529, IP 65 (dust- and waterproof) Weight    1, 6 kg (3.5 lb.) Size (height ™ width)    220 ™ 220 ™ 71 mm (8.7 ™ 8.7 ™ 2.8 in.) Drop test    1.2 m (4 ft.), to MIL STD 810F specifications  (with stand retracted) Environmental Certifications    • Special conditions per certifications • ATEX: II 3 G Ex ic IIC T4 Gc (Ta = –10 °C to 50 °C) • IECEx: Ex ic IIC T4 Gc (Ta = –10 °C to 50 °C) • CE rated • CSA, Class I, Division 2, Groups A, B, C, D, temperature code T4@Ta = 50 °C IP Rating    IP 65 Temperature ratings    • Operating temperature: –10 to 50 °C (14 to 122 °F) • Storage temperature: –20 to 60 °C (–4 to 140 °F) Humidity    10 to 90% relative humidity, non-condensing at   0 to 50 °C (32 to 122 °F) Vibration    MIL STD 810 transportation System, data processing and storage Operating system    Microsoft Windows Embedded CE 6.0 Processor    Marvell PXA320 806 MH DSP    Freescale DSP56311 Internal RAM    • 128 MB DDR SDRAM • 128 MB NAND Flash Internal storage    120 MB (capable of storing approximately 4 000 spectra) SD card    Can support up to 16 GB Communication    USB User indicator    Blue, green, amber and red LED’s Host software Software    The SKF Microlog GX series connects directly to SKF @ptitude Analyst for SKF Microlog software. The Analysis and Reporting Manager plug-in to SKF @ptitude Analyst provides support for the SKF Microlog application modules. Accessories : 1 Battery, Lithium 7.4 volts 2200 mah (Installed) / 2 Accelerometer /  2 cable 2 meters to Accelerometer  2 Magnetic  /Accelerometer Base / 1 AC / UC Power Supply, Universal 115V  230V / 1 USB Communication Cable and Battery Charging / 1 Serial Communication Cable / 1 Carrying Case / 1 Protective Case / 1 Carrying Strap Skf CMXA80 Microlog Vibration Analyzer - USED