Rt1000 Rt800 Replacement Rubber Tracks 600 * 125 * 62 For Dumper Machinery

Morooka At800 Mst550 Yanmar C60r Yfw55r Rubber Track 600*100*80: Applicable machines  various kinds of dumpers  Material  rubber and steel  Specification 600X125X62 Installation position  Installed on the dumpers  Adaptation Models: Model Size AT800 (ALLTRACK) 600X100X80 CG45 (FIAT HITACHI) 600X100X80 CG45 (HITACHI) 600X100X80 IC45 (IHI) 600X100X80 AT800 (MOROOKA) 600X100X80 MST550 (MOROOKA) 600X100X80 MST800 (MOROOKA) 600X100X80 MST800E (MOROOKA) 600X100X80 MST800V (MOROOKA) 600X100X80 MST800VD (MOROOKA) 600X100X80 C60R (YANMAR) 600X100X80 C60R.1 (YANMAR) 600X100X80 C60R.2 (YANMAR) 600X100X80 YFW55R (YANMAR) 600X100X80 The characteristics of rubber tracks : 1. Rubber tracks cause less damage to roads than steel tracks, and less rutting on soft ground than steel tracks . 2. A benefit to equipment operating in congested areas, rubber tracks make less noise than steel tracks . 3. Rubber tracks permit machines to travel at a higher speed than steel tracks . 4. Rubber tracks insulated machine and operator from vibraion, extedin the service life of machine and decreasing operator's fatigue. 5. The ground pressure of rubbr tracks equipped machinery can be fairly low, about 0.14-2.30 kg/m2, a major reason for its use on wet and soft terrain.  6. The added traction of rubber tracked vehicles permits them to pull twice the load of wheeled vehicles of the same weight.  7. Rubber tracks' pulling performance being twice that of wheels, it permits the lighter vehicles equip with rubber track to do the same pulling work than that of wheeled vehicles.  The notices of using rubber tracks  1. Adjust the tension of the rubber crawler so that the height, the variable range is 10-20mm when the machine is lifted. Readjust when the tension decreases. (Be careful because the rubber crawler may come off if the tension is too low).  2. Avoid projection from the frame around the rubber crawler, especially on its inner circumference. (Rubber crawlers are easily deformed; If it comes into contact with the frame, an accident such the rubber being cut can occur).  3. Avoid sharp projections when traveling.  4. Avoid turning too fast on concrete roads with a high coefficient of frction because this can cause accidents such as cutting the rubber.  5. Be careful that no oil, etc adheres to the rubber track. If it does, wipe it off immediately.  6. When storing for long periods, keep indoors, away from direct sunshine and rain.  7. Replace as soon as possible when abrasion of sprockets is observed Parameters: size width*pitch link A B C D F pattern guiding 130*72 29-40 23 64.5 28 28 15 AF1 A2 150*60 32-40 22 64 22.5 24.5 15 AC A2 150*72 29-40 23 64 23 23 15 AC A2 170*60 30-40 19 57 22 22 13 CE A1 180*60 30-40 23.5 64 21 21.5 15 AM A1 180*72 31-43 25 68 29 29 15 BK A2 180*72K 32-48 20 61 22 19.5 17 BB1 B2 B180*72 31-43 23 66 30 29 15 BB1 B2 H180*72 30-50 23 64 27 26 17 BK A2 190*60 30-40 23.5 64 21 21.5 14 AM A1 190*72 31-41 21 68 27.5 26.5 15 BF A2 200*72 34-47 23 76 28.5 26.5 18 BB1 A2 200*72K 37-47 21 69 29.5 29 18 BM A2 Y200*72 40-52 24 64 28.5 29.5 12 BK A2 230*48 60-84 24 72 24 25 21 BI B1 230*48K 60-84 24 66 21 20 19 BI B2 230*72 42-56 24 82 30 26 18 AF1 A2 230*72K 42-56 20 69 29.5 28 16 BD A2 230*96 30-48 25 68 23.5 25.5 22 BE B1 230*101 30-36 25 74 22.5 29 19 BO B1 250*47K 84 23 70 24 20 22 BD B2 250*48.5K 80-88 24 66 21 20 19 CA B2 250*52.5K 72-78 26 81 23 25 25 BA B2 250*52.5 72-78 29 72 23 25 21 BI B1 250*72 47-57 24 82 30 26 18 AF1 A2 B250*72 34-60 23 64 29 22 10 CI A2 B250*72B 34-60 23 78 29 26 16 AB B2 250*96 35-38 25 70 20 19 22 BB1 B2 250*109 35-38 40 89 24.5 14 20 CG B1 260*55.5K 74-80 31 80 21.5 27 24 CA B2 Y260*96 38-41 25 68 23 25.5 22 AB B1 260*109 35-39 30 84 24 29 15 AB B1 E280*52.5K 70-88 29 84 27 26 22 BI B2 280*72 45-64 25 78 29.5 26 22 AL A2 Y280*106K 35-42 30 80 27.5 28 20 AB B2 300*52.5N 72-98 30 82 25 18 20 BI B1 300*52.5W 72-92 43 96 22 23 22 BE B1 300*52.5K 70-84 29 84 27 26 22 BI B2 300*52.5KW 72-92 40 92 25 24 22 BI C1 E300*52.5K 70-88 29 84 27 26 22 BI B2 KB300*52.5 72-92 40 90 24.5 24.5 22 BI C1 KB300*52.5N 72-98 30 82 23 20 25 BI B1 JD300*52.5N 72-98 30 80 23.5 22 22 BI B1 300*53K 80-96 31 88 25 19.5 21 BI B2 300*55 70-88 29 86 25.5 27.5 23 BI B1 300*55.5K 76-82 31 82 22 27 21.5 CA B2 300*71K 72-76 42 106 23 24 40 BD B2 300*72 36-40 23 75 40 34 18 BK A2 BA300*72 36-46 26 76 29 27 19 AF1 A2 300*109N 35-42 29 82 27 28 25 BE B1 300*109W 35-44 38 90 26 29 24 BB1 B1 K300*109 37-41 27 85 23.5 27.5 20 AB B2 300*109WK 35-42 40 90 24.5 14 23 CG B1 320*52.5 72-98 30 83 23.5 18 21 BI B1 320*54 70-84 29 80 23 21 20 AB B1 B320*55K 70-88 30 82 25 30 23 BE B2 Y320*106K 39-43 31 80 26 27 24 AB B2 350*52.5 70-92 40 94 22.5 19 30.5 BE B1 E350*52.5K 70-88 29 84 27 26 22 BI B2 350*54.5K 80-86 40 92 23.5 22.5 23 AD B2 B350*55K 70-88 30 82 25 30 23 BE B2 350*56 80-86 39 89 25.5 16.5 20.5 BC B1 350*75.5K 74 37 98 24.5 25 25 CA C2 350*108 40-46 40 90 24.5 14 25 CG B1 350*109 41-44 40 92 26 20 25 BO B1 Y370*107K 39-41 38 94 25.5 28 23.5 AB B2 400*72.5N 70-80 38 100 26 24 25 AF3 B1 400*72.5W 68-92 51 108 26 24 25 BI B1 Y400*72.5K 72-74 28 86 30 24.5 25 AF3 C2 KB400*72.5K 68-76 37 94 24 26 23.5 BA B2 400*72.5KW 68-92 46 112 24 23.5 25 BI B2 400*74 68-76 38 100 25.5 29.5 24 BH2 B1 400*75.5K 74 39 100 25 26 25 CA C2 Y400*107K 46 38 89 27 25 25 AB C2 K400*142 36-37 27 87 34 27 29 CF C2 400*144 36-41 47 98 27 11 30 CF B1 Y400*144K 36-41 35 126 29.5 26 25 BE B2 450*71 76-88 42.5 115 29.5 17 30 BE B1 DW450*71 76-88 44 114 31 27 25 BD B1 450*73.5 76-84 42 118 31 34 28 CG B1 450*76 80-84 48 122 30.5 31.5 26 BI B1 450*81N 72-80 42 117 26 24 27 BE B1 450*81W 72-78 58 140 29 32 30 BI B1 KB450*81.5 72-80 42 110 31.5 27.5 26 BD B1 K450*83.5 72-74 42 112 24.5 25 28 BI B1 Y450*83.5K 72-74 38 113 24 27 26 CA B2 K450*163 38 38 114 27 28 30 AB B2 485*92W 74 62 142 34 33 30 BE B2 K500*71 72-76 41 106 23 24 42 BE B2 500*92 72-84 48 130 27 26 29 BI B1 500*92W 78-84 64 155 32.5 35.5 33 BI B1 K500*146 35 40 106 26.5 24.5 50 BB1 A2 Warehouse: