Harpye Full-body Harness Double Lanyard Type, Full-body Harness Type 1

Harpye Full-body Harness Double Lanyard type, Full-body Harness Type 1 Description Key Features + Purpose • Passed on JIS T8165 Fall arrest protection standard test (by Technology Institution of Industrial Safety) • Light weight (2.3kg) using aluminum alloy while ensuring strength • Used rust resistant aluminum-magnesium alloy • One-touch buckles on both chest and waist belt • Shoulder/back pads for weight distribution are included • Reflection belt which enhances visibility on dark workplaces • Applied X and V type harness which has high stability on shoulders and legs Specification • Type 1 full-body harness • Free fall distance – 1.8m • Total fall distance – 4.5m (depends on the condition) • Hook for lanyard – above 11.5kN • D ring for lanyard – above 11.5kN • Belt – above 27kN, 44mm • Lanyard – 22kN How to Use 1. Make sure to inspect the full-body harness before use. 2. Wear it passing your arms through the shoulder belt. 3. Fasten the buckles of the chest and waist belts until you hear a click and adjust the length of the belt 4. Pass through the leg buckle and adjust the length. 5. Connect the lanyard to the D-ring on your back and double lock the ring to secure it. Cautions Do not remove the transparent protective cover from the shock absorber. • Do not use lanyard if the transparent cover of shock absorber has been damaged • Wear the harness in the correct way and adjust it without any slack. Incorrect installation may compress the body while falling. • Be careful not to twist each belt. Torsional installation can cause the body to be pressed or penetrate when falling. FAQ 1. What are the three main changes that will be fully enforced (mandatory) from January 2, 2022 due to the revision of the law? (1) The name has changed from "safety belt" to "fall prevention equipment". (2) A full harness type fall prevention device must be used at a distance of 6.75 m or more (5 m in the construction industry). (3) If you use a full harness type fall prevention device at a distance of 2 m or more, you will be required to take special education. (Confirmed by Labor Standards Inspection Office on November 12, 2018) (4) The standard for each item of the new standard has become higher. Please refer to the Ministry of Health, Labor and Welfare guidelines for detailed standards. 2. How can I check the products that conform to the new standard? Since the fall-prevention device is a self-certified product, it is a product that proves itself to be a product that complies with the "standards for fall-prevention device". It is recommended to select products that have received the new standard conformity judgment of the Japan Industrial Safety Technology Association (TIIS) certified by the Ministry of Health, Labor and Welfare. 3. What is the difference between the full harness type and the torso belt type? According to Article 2.1 of the "Standardization of Fall Prevention Equipment" (Usage Restriction), the fall prevention equipment used at a height exceeding 6.75 m must be a full harness type. When working at a height lower than that, the use of a torso belt type is permitted, For safety, the Ministry of Health, Labor and Welfare recommends a full harness type even if it is 2M or more and 6.75M or less (5M for the construction industry) or less. 4. What type of full harness do you have? X type: Strong body fixing force, excellent stability and fit. It is a standard type adopted all over the world. Y type: Since there are few joints on the torso belt and the waist area can be used widely, it is ideal for attaching waist tools. 5. What is the estimated time to replace the full harness and lanyard? Full harness is about 3 years and lanyard is about 2 years. Even if it is unused, it cannot be used if it has been manufactured for more than 7 years. 6. What is the washing method? Hand wash in lukewarm water with a mild detergent. After washing, lightly squeeze it and dry it in a well-ventilated shade away from direct sunlight.